{"id":7078002,"date":"2026-11-11T14:06:46","date_gmt":"2026-11-11T14:06:46","guid":{"rendered":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002"},"modified":"2026-11-11T14:06:46","modified_gmt":"2026-11-11T14:06:46","slug":"john-deere-combine-settings-for-soybeans-a-complete-setup-and-field-tuning-guide","status":"publish","type":"post","link":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002","title":{"rendered":"John Deere Combine Settings for Soybeans: A Complete Setup and Field-Tuning Guide"},"content":{"rendered":"<p> <br \/>\n<\/p>\n<div xmlns:default=\"http:\/\/www.w3.org\/2000\/svg\">\n<p class=\"wp-block-paragraph\">Late October is when soybean moisture swings the hardest. A field can thresh clean at two in the afternoon and turn rubbery by dusk, and the combine that looked perfect at lunch is suddenly dumping split beans into the tank. Anyone who has run beans this time of year knows that no single number on the cab display stays right all day.<\/p>\n<p class=\"wp-block-paragraph\">That is why a good set of <a href=\"https:\/\/www.estesperformanceconcaves.com\/tips-and-tricks-of-john-deere-combine-settings-for-soybeans-for-harvesting\/\">John Deere combine settings for soybeans<\/a> is a starting point, not a finish line. This guide walks through the baseline numbers Deere publishes for its S-Series and X Series combines, explains why each setting matters, shows you how to fine-tune in the field, and covers the mistakes that quietly cost bushels. It is written for first-time operators and seasoned hands alike, so skim what you already know.<\/p>\n<blockquote class=\"wp-block-quote is-layout-flow wp-block-quote-is-layout-flow\">\n<p class=\"wp-block-paragraph\"><strong>Key points<\/strong><\/p>\n<ul class=\"wp-block-list\">\n<li>Deere\u2019s S-Series baseline for soybeans is about 580 rpm rotor speed, concave clearance of 25, and fan speed near 980 rpm. X Series machines use different, faster rotor numbers because of their dual rotors.<\/li>\n<li>Start harvesting beans at about 14 to 15 percent moisture to limit splits and seed-coat cracking.<\/li>\n<li>Most soybean harvest loss happens at the header, not inside the machine, so set up the cutterbar and reel before touching the rotor.<\/li>\n<li>Four soybeans per square foot on the ground equals roughly one bushel per acre lost.<\/li>\n<li>Do not close the sieve to clean up your sample. Raise fan speed first.<\/li>\n<li>Check your settings every couple of hours as the crop dries down during the day.<\/li>\n<\/ul>\n<\/blockquote>\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Where_should_John_Deere_combine_settings_for_soybeans_start\"\/>Where should John Deere combine settings for soybeans start?<span class=\"ez-toc-section-end\"\/><\/h2>\n<p class=\"wp-block-paragraph\">Start with the manufacturer\u2019s baseline, then adjust for what the crop is actually doing. Deere\u2019s Harvester Works publishes \u201cReady to Harvest\u201d guides for soybeans for both the S-Series and the X Series, and they are explicit that the numbers are a pre-season starting point. Moisture, stem condition, and weather all push you away from them once you are in the field.<\/p>\n<p class=\"wp-block-paragraph\">The logic behind the baseline is simple. Soybeans are fragile compared to corn. The seed is easy to crack, the pods shatter if they are hit hard, and the stems can be bone dry or still green depending on the variety and the weather. Good <a href=\"https:\/\/www.estesperformanceconcaves.com\/john-deere-combine-settings-soybeans\/\">soybean settings<\/a> therefore aim to thresh just enough to open the pods, move the material through quickly, and keep the cleaning shoe from being overloaded.<\/p>\n<p class=\"wp-block-paragraph\">Work in this order every time: header first, then the feeding and threshing components, then the cleaning shoe, then a loss check. Fixing things out of order is how operators end up chasing a problem at the rotor that really started at the reel.<\/p>\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"What_moisture_level_is_best_for_harvesting_soybeans\"\/>What moisture level is best for harvesting soybeans?<span class=\"ez-toc-section-end\"\/><\/h2>\n<p class=\"wp-block-paragraph\">Deere\u2019s grain-quality guidance says to begin at roughly 14 to 15 percent moisture to avoid splits and seed-coat cracking, and warns that once seed falls below 10 to 11 percent it becomes difficult to prevent damage. At 10 percent or drier, Deere\u2019s advice is to park the combine and wait for the beans to take on moisture overnight or after a rain, because you will see splits no matter how you set the machine. University extension programs generally describe an ideal window of about 12 to 15 percent.<\/p>\n<p class=\"wp-block-paragraph\">In practical terms, a bean that rattles loudly in the pod and snaps cleanly is usually drying fast. Pull a handful, test it with a moisture meter, and decide whether you are in the safe zone before you blame the concaves for a bad sample.<\/p>\n<h2 class=\"wp-block-heading\">How should you set up the header for soybeans?<span class=\"ez-toc-section-end\"\/><\/h2>\n<p class=\"wp-block-paragraph\">Set up the header first, because the platform is where most of the loss happens. Extension studies from North Carolina State, Ohio State, Iowa State, and the University of Georgia put gathering loss at the header anywhere from about 75 percent to as high as 90 percent of total soybean <a href=\"https:\/\/www.estesperformanceconcaves.com\/harvest-concaves-minimize-harvest-loss-and-maximize-yield\/\">harvest loss<\/a>, depending on the study. Deere\u2019s own guide states that the highest share of soybean field loss occurs at the cutterbar and reel.<\/p>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Which_knife_sections_and_guards_work_best\"\/>Which knife sections and guards work best?<span class=\"ez-toc-section-end\"\/><\/h3>\n<p class=\"wp-block-paragraph\">Deere recommends coarse-tooth knife sections with blunt-nose guards for soybeans on both draper and auger platforms. Sharp sections, sharp guard edges, and tight hold-downs matter more than any in-cab number. For no-till beans in corn stalks, Deere suggests short\/long sections with non-clog guards, which have the cross bar removed so stalks do not hairpin and push. For double-crop beans in wheat stubble, open-top guards with long coarse-tooth sections help prevent plugging.<\/p>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Where_should_the_reel_sit_and_how_fast_should_it_turn\"\/>Where should the reel sit, and how fast should it turn?<span class=\"ez-toc-section-end\"\/><\/h3>\n<p class=\"wp-block-paragraph\">On a flex draper, the reel only has to nudge crop over the cutterbar onto the belts, so Deere calls for running it up and out. On a flex auger platform, the reel runs low and back to pull crop to the auger. When setting up with the cutterbar locked up, Deere suggests a reel clearance of about 1.5 inches above the knife guards.<\/p>\n<p class=\"wp-block-paragraph\">For reel speed, Deere says to match or slightly exceed ground speed in standing beans, so the reel looks like it is pulling the combine through the field. In down or tangled beans, run it about 50 percent faster than ground speed. Extension engineers commonly give a general rule of about 25 percent faster than travel speed in normal crop. Too fast shatters pods, and a reel that rides too low does the same.<\/p>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"What_reel_finger_pitch_should_you_use\"\/>What reel finger pitch should you use?<span class=\"ez-toc-section-end\"\/><\/h3>\n<ul class=\"wp-block-list\">\n<li>Most aggressive (pulled back) for down or tangled beans<\/li>\n<li>Medium (leaned back) for normal standing beans<\/li>\n<li>Least aggressive (straight down) for tall, standing crop<\/li>\n<\/ul>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"How_low_should_the_header_run_and_how_fast_should_the_draper_belts_go\"\/>How low should the header run, and how fast should the draper belts go?<span class=\"ez-toc-section-end\"\/><\/h3>\n<p class=\"wp-block-paragraph\">Run the cutterbar as close to the ground as you can and parallel to it, so you do not leave low pods behind on the stems. Automatic header height sensing helps, but it has to be calibrated before you start. On draper heads, Deere\u2019s X Series guide describes ideal belt speed as the point where the two side-belt streams barely meet in the middle, forming one smooth, wide stream into the feed drum. Too slow and crop bunches at the outsides; too fast and the streams collide, causing slug feeding.<\/p>\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"What_are_the_baseline_in-cab_John_Deere_combine_settings_for_soybeans\"\/>What are the baseline in-cab John Deere combine settings for soybeans?<span class=\"ez-toc-section-end\"\/><\/h2>\n<p class=\"wp-block-paragraph\">The numbers below come from Deere\u2019s Ready to Harvest soybean guides. Remember that these are starting values. Your combine\u2019s model year, your variety, and the day\u2019s moisture will move them.<\/p>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"What_are_the_S-Series_baseline_settings\"\/>What are the S-Series baseline settings?<span class=\"ez-toc-section-end\"\/><\/h3>\n<ul class=\"wp-block-list\">\n<li>Rotor speed: 580 rpm. Use about 500 rpm in dry stems and up to 600 rpm in green stems.<\/li>\n<li>Concave clearance: 25 on the cab display, with round bar concaves in all three positions.<\/li>\n<li>Cleaning fan speed: about 980 rpm.<\/li>\n<li>Deep-tooth chaffer: 14, with the dual zone rear opening at 5. General purpose chaffer: 16, with the rear opening at 5.<\/li>\n<li>Sieve opening: 8.<\/li>\n<li>Backshaft speed: 500 to 530 rpm on the variable drive, or first gear on a five-speed drive.<\/li>\n<li>Feed accelerator: low speed with serrated wear strips.<\/li>\n<li>Chopper: high speed. On S680 and S690 machines, put the active tailings lever in the open (corn) position.<\/li>\n<\/ul>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"What_are_the_X_Series_baseline_settings\"\/>What are the X Series baseline settings?<span class=\"ez-toc-section-end\"\/><\/h3>\n<p class=\"wp-block-paragraph\">The X Series uses dual 24-inch rotors, which are smaller than the single 30-inch rotor on the S-Series. Deere says the rotors need to spin faster to match the equivalent tip speed, so the rpm numbers look much higher. The in-cab soybean window in Deere\u2019s X Series guide is:<\/p>\n<ul class=\"wp-block-list\">\n<li>Rotor speed: 900 to 1,300 rpm<\/li>\n<li>Concave clearance: 7 to 26 mm<\/li>\n<li>Cleaning fan speed: 800 to 1,000 rpm<\/li>\n<li>Deep-tooth chaffer: 12 to 20 mm. General purpose chaffer: 13 to 21 mm.<\/li>\n<li>Deep-tooth sieve: 4 to 12 mm. General purpose sieve: 5 to 13 mm.<\/li>\n<li>Backshaft speed: 510 rpm<\/li>\n<li>Front chaffer: 25 mm for all crops. Closing it can choke airflow and cut capacity.<\/li>\n<\/ul>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"How_do_the_S-Series_and_X_Series_settings_compare_side_by_side\"\/>How do the S-Series and X Series settings compare side by side?<span class=\"ez-toc-section-end\"\/><\/h3>\n<figure class=\"wp-block-table\">\n<table class=\"has-fixed-layout\">\n<thead>\n<tr>\n<th>Setting<\/th>\n<th>S-Series baseline<\/th>\n<th>X Series window<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Rotor speed<\/td>\n<td>580 rpm (500 dry stems, 600 green)<\/td>\n<td>900 to 1,300 rpm<\/td>\n<\/tr>\n<tr>\n<td>Concave type<\/td>\n<td>Round bar, all three positions<\/td>\n<td>Round bar, all three positions<\/td>\n<\/tr>\n<tr>\n<td>Concave clearance<\/td>\n<td>25 (cab display)<\/td>\n<td>7 to 26 mm<\/td>\n<\/tr>\n<tr>\n<td>Cleaning fan<\/td>\n<td>About 980 rpm<\/td>\n<td>800 to 1,000 rpm<\/td>\n<\/tr>\n<tr>\n<td>Chaffer<\/td>\n<td>Deep tooth 14 or general purpose 16<\/td>\n<td>Deep tooth 12 to 20 mm or general purpose 13 to 21 mm<\/td>\n<\/tr>\n<tr>\n<td>Sieve<\/td>\n<td>8<\/td>\n<td>Deep tooth 4 to 12 mm or general purpose 5 to 13 mm<\/td>\n<\/tr>\n<tr>\n<td>Backshaft speed<\/td>\n<td>500 to 530 rpm<\/td>\n<td>510 rpm<\/td>\n<\/tr>\n<tr>\n<td>Feed accelerator<\/td>\n<td>Low speed<\/td>\n<td>Low speed, first gear<\/td>\n<\/tr>\n<tr>\n<td>Active tailings<\/td>\n<td>Open (corn) position on S680\/S690<\/td>\n<td>Open (corn) position<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/figure>\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Which_concaves_work_best_for_soybeans_on_a_John_Deere_combine\"\/>Which concaves work best for soybeans on a John Deere combine?<span class=\"ez-toc-section-end\"\/><\/h2>\n<p class=\"wp-block-paragraph\">Deere recommends round bar concaves in all three positions for soybeans, since they perform well across moisture conditions and their open areas let beans fall through quickly, which cuts grain damage. Large wire concaves are an option, but Deere warns they carry a risk of hairpin plugging in green-stem beans.<\/p>\n<p class=\"wp-block-paragraph\">Whichever you run, level the concaves front to rear and zero the concave position sensor. A concave that is tight in the rear or too tight in the front creates a pinch point, which means poor <a href=\"https:\/\/www.estesperformanceconcaves.com\/combine-threshing\/\">threshing<\/a> and cracked beans. This is one of the most overlooked ten-minute jobs of the season.<\/p>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Where_do_aftermarket_concaves_like_Estes_XPR3_fit_in\"\/>Where do aftermarket concaves like Estes XPR3 fit in?<span class=\"ez-toc-section-end\"\/><\/h3>\n<p class=\"wp-block-paragraph\">The factory round bar and wire concaves are designed to be swapped as crops change, and many growers also add cover plates or inserts when conditions get tricky. Estes Performance Concaves built the <a href=\"https:\/\/www.estesperformanceconcaves.com\/product\/xpr-3-concaves\/\">XPR3 Concave System<\/a> around a different idea: one set that works across crops without changing concaves or adding covers and inserts. Estes reports 135 percent more threshing surface area than a round bar concave, a 143-finger Xtreme Separation Grate designed to keep grain escaping through the crop mat, and a capacity gain of about 70 percent. In the field, Estes says that translates to running about 2 to 3 mph faster and stopping the 3 to 5 bushels per acre that rotor loss can take on standard concaves.<\/p>\n<p class=\"wp-block-paragraph\">If you run XPR3 concaves, do not assume Deere\u2019s factory baseline fits perfectly. The system is designed to work effectively at lower rotor speeds, so start at the low end of your rotor range, then confirm with a power shutdown and loss check. The Estes support team can help match settings to your combine model.<\/p>\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"How_do_you_adjust_rotor_speed_and_concave_clearance_for_soybeans\"\/>How do you adjust rotor speed and concave clearance for soybeans?<span class=\"ez-toc-section-end\"\/><\/h2>\n<p class=\"wp-block-paragraph\">Rotor speed and concave clearance work as a pair. Deere\u2019s guidance gives a clear order of operations:<\/p>\n<ul class=\"wp-block-list\">\n<li>If you see splits or cracked beans in the tank, open the concave in steps of about 5 before touching rotor speed. Rotor speed also drives material handling in the separator, so leave it alone if you can.<\/li>\n<li>If unthreshed pods show up in the tank, close the concave 1 to 2 at a time until they disappear. There is a fine line between splits and unthreshed pods, and small moves keep you on the right side of it.<\/li>\n<li>If stems are damp or green, bump rotor speed up toward 600 rpm on an S-Series machine rather than closing the concave hard.<\/li>\n<\/ul>\n<p class=\"wp-block-paragraph\">A useful field trick from soybean-harvest tip lists is to raise rotor speed until the first cracked beans appear in the tank, then back off about 10 rpm. Iowa State extension offers a similar approach in plain language: start at the low end of the recommended rotor speed and wider concave setting, then tighten in small steps, only enough to avoid unthreshed pods.<\/p>\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"How_do_you_set_fan_speed_chaffer_and_sieve_for_a_clean_sample\"\/>How do you set fan speed, chaffer, and sieve for a clean sample?<span class=\"ez-toc-section-end\"\/><\/h2>\n<p class=\"wp-block-paragraph\">Think of the cleaning shoe as an air-and-screen filter. The fan lifts light material, the chaffer lets beans and small pieces fall, and the sieve catches clean beans while sending the rest to tailings.<\/p>\n<p class=\"wp-block-paragraph\">When threshed pods or small sticks show up in the grain tank, Deere\u2019s grain-sample checklist says to work through the following, in order:<\/p>\n<ul class=\"wp-block-list\">\n<li>Confirm the concaves are level and zeroed.<\/li>\n<li>Confirm the chaffer and sieve openings match what the cab display says. If they do not, run the factory calibration procedure.<\/li>\n<li>Tighten the chaffer opening by about 2 mm to help remove sticks and pieces.<\/li>\n<li>Increase fan speed in 50 rpm steps until you see shoe loss, then back off.<\/li>\n<li>Recheck every two hours as the crop dries.<\/li>\n<\/ul>\n<p class=\"wp-block-paragraph\">Notice what is missing: closing the sieve. Deere is blunt about this. Closing the sieve pushes free, clean beans into the tailings and sets them up for re-threshing damage. A related extension tip says the same thing from the other direction: an overloaded chaffer needs far more air to clear stems and pods, so keep the shoe from overloading in the first place.<\/p>\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"How_can_you_tell_if_your_settings_are_actually_working\"\/>How can you tell if your settings are actually working?<span class=\"ez-toc-section-end\"\/><\/h2>\n<p class=\"wp-block-paragraph\">Run a power shutdown. Deere\u2019s procedure is to harvest a short distance, shut down the separator and engine, then inspect the machine and the ground. Drop open the tailings elevator door. In soybeans, you should find no free beans in the tailings at all. If you do, the shoe is losing the fight, and the fix is airflow and screen openings, not a tighter sieve.<\/p>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"How_do_you_measure_soybean_harvest_loss\"\/>How do you measure soybean harvest loss?<span class=\"ez-toc-section-end\"\/><\/h3>\n<p class=\"wp-block-paragraph\">Use the counting method taught by extension programs across the country:<\/p>\n<ol class=\"wp-block-list\">\n<li>Check pre-harvest loss in an unharvested area first, since shatter and lodging happen before you arrive.<\/li>\n<li>Check header loss by stopping at speed and backing up about 20 feet, then counting beans in front of where the header ran.<\/li>\n<li>Check total loss behind the combine and subtract the earlier counts to isolate machine loss.<\/li>\n<\/ol>\n<p class=\"wp-block-paragraph\">The rule of thumb is that four soybeans per square foot equals about one bushel per acre. Extension specialists generally treat a total harvest loss of 3 percent or less as acceptable. In a 50-bushel field, that is roughly 1.5 bushels per acre, or about six beans per square foot. Deere\u2019s Equipment Plus app includes a grain loss calculator that does the math for you, and X Series and S-Series machines built from model year 2022 on ship with an area-based loss display algorithm by default.<\/p>\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"How_do_you_fix_common_soybean_sample_and_loss_problems\"\/>How do you fix common soybean sample and loss problems?<span class=\"ez-toc-section-end\"\/><\/h2>\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-large is-resized\"><a href=\"https:\/\/www.estesperformanceconcaves.com\/wp-content\/uploads\/2026\/05\/soybean.png\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"512\" src=\"https:\/\/www.estesperformanceconcaves.com\/wp-content\/uploads\/2026\/05\/soybean-1024x512.png\" alt=\"Soybean Threshing\" class=\"wp-image-5316\" style=\"width:604px;height:auto\" srcset=\"https:\/\/www.estesperformanceconcaves.com\/wp-content\/uploads\/2026\/05\/soybean-1024x512.png 1024w, https:\/\/www.estesperformanceconcaves.com\/wp-content\/uploads\/2026\/05\/soybean-300x150.png 300w, https:\/\/www.estesperformanceconcaves.com\/wp-content\/uploads\/2026\/05\/soybean-1536x768.png 1536w, https:\/\/www.estesperformanceconcaves.com\/wp-content\/uploads\/2026\/05\/soybean-500x250.png 500w, https:\/\/www.estesperformanceconcaves.com\/wp-content\/uploads\/2026\/05\/soybean.png 1774w, https:\/\/www.estesperformanceconcaves.com\/wp-content\/uploads\/2026\/05\/soybean-300x150@2x.png 600w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\"\/><\/a><\/figure>\n<\/div>\n<ul class=\"wp-block-list\">\n<li><strong>Splits and cracked beans:<\/strong> Beans may be too dry. If moisture is fine, open the concave a few clicks, then check level and calibration.<\/li>\n<li><strong>Unthreshed pods in the tank:<\/strong> Close the concave 1 to 2 at a time. If stems are green, raise rotor speed a bit.<\/li>\n<li><strong>Pods and sticks in the tank:<\/strong> Raise fan speed in 50 rpm steps and tighten the chaffer by about 2 mm.<\/li>\n<li><strong>Shatter loss at the header:<\/strong> Match reel speed to ground speed, raise the reel if it rides low, check for dull knife sections, and slow down.<\/li>\n<li><strong>Down and tangled beans:<\/strong> Pull finger pitch back, tilt the feeder house forward to nose down the cutterbar, add crop lifters or rod dividers, and cut at a 45-degree angle to the lodging direction.<\/li>\n<li><strong>Beans in the tailings:<\/strong> Open the chaffer or raise fan speed instead of closing the sieve.<\/li>\n<\/ul>\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Can_John_Deere_automation_set_these_combine_settings_for_you\"\/>Can John Deere automation set these combine settings for you?<span class=\"ez-toc-section-end\"\/><\/h2>\n<p class=\"wp-block-paragraph\">Partly. Deere\u2019s automation systems can set and adjust most of the numbers above. On S700 machines, the Automatic Combine Adjustment function presets rotor speed, fan speed, concave clearance, and more for the selected condition, then lets you fine-tune with plus and minus buttons. Deere\u2019s Harvest Settings Automation goes further, adjusting rotor speed, concave clearance, sieve, chaffer, and fan speed from a few operator inputs, and slowing the fan when the machine leaves a field into harvested ground so grain does not blow out.<\/p>\n<p class=\"wp-block-paragraph\">Automation is a strong starting point, but it cannot see your sample. Treat it the same way you treat any baseline. Run the power shutdown, check the tailings, and use the loss numbers to confirm that the system is hitting your targets. For anyone learning John Deere combine settings for soybeans, those in-cab presets also make a handy reference for how the settings change from dry to green conditions.<\/p>\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"What_are_the_pros_and_cons_of_upgrading_to_XPR3_concaves_for_soybean_harvest\"\/>What are the pros and cons of upgrading to XPR3 concaves for soybean harvest?<span class=\"ez-toc-section-end\"\/><\/h2>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"What_are_the_pros\"\/>What are the pros?<span class=\"ez-toc-section-end\"\/><\/h3>\n<ul class=\"wp-block-list\">\n<li>One concave set across crops, so no swapping or adding covers between corn and beans.<\/li>\n<li>More threshing surface area (135 percent more than a round bar, per Estes) so grain is threshed and out of the rotor sooner.<\/li>\n<li>Potential for 2 to 3 mph faster sustainable ground speed, which adds acres per day.<\/li>\n<li>The Xtreme Separation Grate is available as part of a complete threshing and separation upgrade, not just a single part swap.<\/li>\n<li>Designed to retain more grain, with Estes citing 3 to 5 bushels per acre of rotor loss on standard concaves.<\/li>\n<\/ul>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"What_are_the_cons\"\/>What are the cons?<span class=\"ez-toc-section-end\"\/><\/h3>\n<ul class=\"wp-block-list\">\n<li>Upfront cost, which you need to weigh against your acres and grain price.<\/li>\n<li>Installation time and labor, especially if you add the separation grate.<\/li>\n<li>Higher ground speeds can need more engine horsepower, so results depend on your combine model.<\/li>\n<li>Your baseline settings will shift, so plan time to retune rotor speed, concave clearance, and fan speed.<\/li>\n<\/ul>\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"What_are_the_most_common_mistakes_with_soybean_combine_settings\"\/>What are the most common mistakes with soybean combine settings?<span class=\"ez-toc-section-end\"\/><\/h2>\n<ol class=\"wp-block-list\">\n<li><strong>Closing the sieve to clean the sample.<\/strong> It sends clean beans through the tailings and causes damage. Raise fan speed or tighten the chaffer slightly instead.<\/li>\n<li><strong>Reaching for rotor speed first.<\/strong> Splits are usually fixed by opening the concave, since rotor speed also controls how well material moves through the separator.<\/li>\n<li><strong>Running the reel too fast or too low.<\/strong> This shatters pods, and the header is where most of your loss lives.<\/li>\n<li><strong>Setting once and forgetting.<\/strong> Beans dry down through the day, so settings that were right at noon can be wrong by four. Check every two hours.<\/li>\n<li><strong>Skipping calibration and leveling.<\/strong> If chaffer, sieve, and concave openings do not match the display, or the concaves are out of level, your settings are fiction.<\/li>\n<\/ol>\n<h2 class=\"wp-block-heading has-text-align-center has-large-font-size\"><span class=\"ez-toc-section\" id=\"Frequently_Asked_Questions\"\/>Frequently Asked Questions<span class=\"ez-toc-section-end\"\/><\/h2>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Are_John_Deere_combine_settings_for_soybeans_the_same_on_every_model\"\/>Are John Deere combine settings for soybeans the same on every model?<span class=\"ez-toc-section-end\"\/><\/h3>\n<p class=\"wp-block-paragraph\">No. The principles are the same, but the numbers differ. An S-Series baseline is about 580 rpm rotor speed with a concave clearance of 25 and a fan near 980 rpm. X Series combines with dual 24-inch rotors run higher rotor speeds, in a 900 to 1,300 rpm in-cab window, with concave clearance of 7 to 26 mm. Check Deere\u2019s Ready to Harvest guide and your operator\u2019s manual for your exact model and year.<\/p>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"What_rotor_speed_should_I_run_in_soybeans_on_a_John_Deere_S-Series_combine\"\/>What rotor speed should I run in soybeans on a John Deere S-Series combine?<span class=\"ez-toc-section-end\"\/><\/h3>\n<p class=\"wp-block-paragraph\">Deere\u2019s baseline is 580 rpm, with about 500 rpm for dry stems and up to 600 rpm for green stems. If you are seeing splits, open the concave before reducing or raising rotor speed, since rotor speed also keeps material moving through the separator.<\/p>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"How_do_I_know_if_my_fan_speed_is_right_for_soybeans\"\/>How do I know if my fan speed is right for soybeans?<span class=\"ez-toc-section-end\"\/><\/h3>\n<p class=\"wp-block-paragraph\">Start near Deere\u2019s S-Series baseline of 980 rpm. If threshed pods or small sticks reach the grain tank, raise the fan in 50 rpm steps until you see shoe loss, then back off. Confirm with a power shutdown that there are no free beans in the tailings.<\/p>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"How_much_soybean_harvest_loss_is_acceptable\"\/>How much soybean harvest loss is acceptable?<span class=\"ez-toc-section-end\"\/><\/h3>\n<p class=\"wp-block-paragraph\">Extension specialists generally consider a total loss of 3 percent of yield or less acceptable. Four soybeans per square foot equals about one bushel per acre. In a 50-bushel field, 3 percent is about 1.5 bushels, or around six beans per square foot.<\/p>\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Can_I_use_my_corn_settings_for_soybeans\"\/>Can I use my corn settings for soybeans?<span class=\"ez-toc-section-end\"\/><\/h3>\n<p class=\"wp-block-paragraph\">No. Soybeans need a lighter threshing touch, and the cleaning shoe changes too. On an S-Series machine, Deere\u2019s soybean baseline uses a sieve opening of 8, while its corn guide lists a sieve range of 10 to 14. Always reset rotor speed, concave clearance, fan speed, and screen openings when you switch crops.<\/p>\n<\/div>\n<p><script>\n\t\t\tvar aepc_pixel = {\"pixel_id\":\"1549200208629764\",\"user\":{},\"enable_advanced_events\":\"yes\",\"fire_delay\":\"0\",\"can_use_sku\":\"yes\",\"enable_viewcontent\":\"yes\",\"enable_addtocart\":\"yes\",\"enable_addtowishlist\":\"no\",\"enable_initiatecheckout\":\"yes\",\"enable_addpaymentinfo\":\"yes\",\"enable_purchase\":\"yes\",\"allowed_params\":{\"AddToCart\":[\"value\",\"currency\",\"content_category\",\"content_name\",\"content_type\",\"content_ids\"],\"AddToWishlist\":[\"value\",\"currency\",\"content_category\",\"content_name\",\"content_type\",\"content_ids\"]}},\n\t\t\t\taepc_pixel_args = [],\n\t\t\t\taepc_extend_args = function( args ) {\n\t\t\t\t\tif ( typeof args === 'undefined' ) {\n\t\t\t\t\t\targs = {};\n\t\t\t\t\t}\n\t\t\t\t\tfor(var key in aepc_pixel_args)\n\t\t\t\t\t\targs[key] = aepc_pixel_args[key];\n\t\t\t\t\treturn args;\n\t\t\t\t};\n\t\t\t\/\/ Extend args\n\t\t\tif ( 'yes' === aepc_pixel.enable_advanced_events ) {\n\t\t\t\taepc_pixel_args.userAgent = navigator.userAgent;\n\t\t\t\taepc_pixel_args.language = navigator.language;\n\t\t\t\tif ( document.referrer.indexOf( document.domain ) < 0 ) {\n\t\t\t\t\taepc_pixel_args.referrer = document.referrer;\n\t\t\t\t}\n\t\t\t}\n\n\t\t\t\t\t\t!function(f,b,e,v,n,t,s){if(f.fbq)return;n=f.fbq=function(){n.callMethod?\n\t\t\t\tn.callMethod.apply(n,arguments):n.queue.push(arguments)};if(!f._fbq)f._fbq=n;\n\t\t\t\tn.push=n;n.loaded=!0;n.version='2.0';n.agent=\"dvpixelcaffeinewordpress\";n.queue=[];t=b.createElement(e);t.async=!0;\n\t\t\t\tt.src=v;s=b.getElementsByTagName(e)[0];s.parentNode.insertBefore(t,s)}(window,\n\t\t\t\tdocument,'script','https:\/\/connect.facebook.net\/en_US\/fbevents.js');\n\t\t\t\n\t\t\t\t\t\tfbq('init', aepc_pixel.pixel_id, aepc_pixel.user);\n\n\t\t\t\t\t\t\tsetTimeout( function() {\n\t\t\t\tfbq('track', \"PageView\", aepc_pixel_args);\n\t\t\t}, aepc_pixel.fire_delay * 1000 );\n\t\t\t\t\t<\/script><br \/>\n<br \/><\/p>\n","protected":false},"excerpt":{"rendered":"<p>Late October is when soybean moisture swings the hardest. A field can thresh clean at two in the afternoon and turn rubbery by dusk, and the combine that looked perfect at lunch is suddenly dumping split beans into the tank. Anyone who has run beans this time of year knows that no single number on [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":7078003,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[12026],"tags":[15917,15920,15918,3037,17132,15914,236179,2059,3201,15916,5501,7003,14847,15915],"dealstore":[],"offerexpiration":[],"class_list":["post-7078002","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-agriculture","tag-case-ih-concaves","tag-combine","tag-combine-concaves","tag-complete","tag-deere","tag-estes-concaves","tag-fieldtuning","tag-guide","tag-john","tag-john-deere-concaves","tag-settings","tag-setup","tag-soybeans","tag-xpr-concaves"],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v26.4 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>John Deere Combine Settings for Soybeans: A Complete Setup and Field-Tuning Guide - Som2ny Network<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"John Deere Combine Settings for Soybeans: A Complete Setup and Field-Tuning Guide - Som2ny Network\" \/>\n<meta property=\"og:description\" content=\"Late October is when soybean moisture swings the hardest. A field can thresh clean at two in the afternoon and turn rubbery by dusk, and the combine that looked perfect at lunch is suddenly dumping split beans into the tank. Anyone who has run beans this time of year knows that no single number on [&hellip;]\" \/>\n<meta property=\"og:url\" content=\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002\" \/>\n<meta property=\"og:site_name\" content=\"Som2ny Network\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-11T14:06:46+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/accountants4yourbusiness.co.uk\/wp-content\/uploads\/2026\/11\/Combine-Settings-for-Soybeans.webp.webp\" \/>\n\t<meta property=\"og:image:width\" content=\"1717\" \/>\n\t<meta property=\"og:image:height\" content=\"916\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/webp\" \/>\n<meta name=\"author\" content=\"admin\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"admin\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"16 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#article\",\"isPartOf\":{\"@id\":\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002\"},\"author\":{\"name\":\"admin\",\"@id\":\"https:\/\/peraltafinancing.com\/#\/schema\/person\/b8eaddeb20a8727558e0d0cddcca426e\"},\"headline\":\"John Deere Combine Settings for Soybeans: A Complete Setup and Field-Tuning Guide\",\"datePublished\":\"2026-11-11T14:06:46+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002\"},\"wordCount\":3208,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/peraltafinancing.com\/#organization\"},\"image\":{\"@id\":\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#primaryimage\"},\"thumbnailUrl\":\"https:\/\/accountants4yourbusiness.co.uk\/wp-content\/uploads\/2026\/11\/Combine-Settings-for-Soybeans.webp.webp\",\"keywords\":[\"case ih concaves\",\"Combine\",\"combine concaves\",\"Complete\",\"Deere\",\"estes concaves\",\"FieldTuning\",\"Guide\",\"JOHN\",\"john deere concaves\",\"Settings\",\"Setup\",\"soybeans\",\"xpr concaves\"],\"articleSection\":[\"Agriculture\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#respond\"]}]},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002\",\"url\":\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002\",\"name\":\"John Deere Combine Settings for Soybeans: A Complete Setup and Field-Tuning Guide - Som2ny Network\",\"isPartOf\":{\"@id\":\"https:\/\/peraltafinancing.com\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#primaryimage\"},\"image\":{\"@id\":\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#primaryimage\"},\"thumbnailUrl\":\"https:\/\/accountants4yourbusiness.co.uk\/wp-content\/uploads\/2026\/11\/Combine-Settings-for-Soybeans.webp.webp\",\"datePublished\":\"2026-11-11T14:06:46+00:00\",\"breadcrumb\":{\"@id\":\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#primaryimage\",\"url\":\"https:\/\/accountants4yourbusiness.co.uk\/wp-content\/uploads\/2026\/11\/Combine-Settings-for-Soybeans.webp.webp\",\"contentUrl\":\"https:\/\/accountants4yourbusiness.co.uk\/wp-content\/uploads\/2026\/11\/Combine-Settings-for-Soybeans.webp.webp\",\"width\":1717,\"height\":916},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/peraltafinancing.com\/?bp_activities=1\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"John Deere Combine Settings for Soybeans: A Complete Setup and Field-Tuning Guide\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/peraltafinancing.com\/#website\",\"url\":\"https:\/\/peraltafinancing.com\/\",\"name\":\"Som2ny Network\",\"description\":\"Daily Deals\",\"publisher\":{\"@id\":\"https:\/\/peraltafinancing.com\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/peraltafinancing.com\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":\"Organization\",\"@id\":\"https:\/\/peraltafinancing.com\/#organization\",\"name\":\"Som2ny Network\",\"url\":\"https:\/\/peraltafinancing.com\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\/\/peraltafinancing.com\/#\/schema\/logo\/image\/\",\"url\":\"https:\/\/accountants4yourbusiness.co.uk\/wp-content\/uploads\/2026\/07\/4a0953c4-logo-300x86-1.png\",\"contentUrl\":\"https:\/\/accountants4yourbusiness.co.uk\/wp-content\/uploads\/2026\/07\/4a0953c4-logo-300x86-1.png\",\"width\":300,\"height\":86,\"caption\":\"Som2ny Network\"},\"image\":{\"@id\":\"https:\/\/peraltafinancing.com\/#\/schema\/logo\/image\/\"}},{\"@type\":\"Person\",\"@id\":\"https:\/\/peraltafinancing.com\/#\/schema\/person\/b8eaddeb20a8727558e0d0cddcca426e\",\"name\":\"admin\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\/\/peraltafinancing.com\/#\/schema\/person\/image\/\",\"url\":\"https:\/\/secure.gravatar.com\/avatar\/729ae85bf62b9917e93538db2f2688ca?s=96&r=g&default=https%3A%2F%2Faccountants4yourbusiness.co.uk%2Fwp-content%2Fplugins%2Fbuddypress-first-letter-avatar%2Fimages%2Fdefault%2F96%2Flatin_a.png\",\"contentUrl\":\"https:\/\/secure.gravatar.com\/avatar\/729ae85bf62b9917e93538db2f2688ca?s=96&r=g&default=https%3A%2F%2Faccountants4yourbusiness.co.uk%2Fwp-content%2Fplugins%2Fbuddypress-first-letter-avatar%2Fimages%2Fdefault%2F96%2Flatin_a.png\",\"caption\":\"admin\"},\"sameAs\":[\"https:\/\/accountants4yourbusiness.co.uk\"],\"url\":\"https:\/\/accountants4yourbusiness.co.uk\/?author=1\"}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"John Deere Combine Settings for Soybeans: A Complete Setup and Field-Tuning Guide - Som2ny Network","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002","og_locale":"en_US","og_type":"article","og_title":"John Deere Combine Settings for Soybeans: A Complete Setup and Field-Tuning Guide - Som2ny Network","og_description":"Late October is when soybean moisture swings the hardest. A field can thresh clean at two in the afternoon and turn rubbery by dusk, and the combine that looked perfect at lunch is suddenly dumping split beans into the tank. Anyone who has run beans this time of year knows that no single number on [&hellip;]","og_url":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002","og_site_name":"Som2ny Network","article_published_time":"2026-11-11T14:06:46+00:00","og_image":[{"width":1717,"height":916,"url":"https:\/\/accountants4yourbusiness.co.uk\/wp-content\/uploads\/2026\/11\/Combine-Settings-for-Soybeans.webp.webp","type":"image\/webp"}],"author":"admin","twitter_card":"summary_large_image","twitter_misc":{"Written by":"admin","Est. reading time":"16 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#article","isPartOf":{"@id":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002"},"author":{"name":"admin","@id":"https:\/\/peraltafinancing.com\/#\/schema\/person\/b8eaddeb20a8727558e0d0cddcca426e"},"headline":"John Deere Combine Settings for Soybeans: A Complete Setup and Field-Tuning Guide","datePublished":"2026-11-11T14:06:46+00:00","mainEntityOfPage":{"@id":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002"},"wordCount":3208,"commentCount":0,"publisher":{"@id":"https:\/\/peraltafinancing.com\/#organization"},"image":{"@id":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#primaryimage"},"thumbnailUrl":"https:\/\/accountants4yourbusiness.co.uk\/wp-content\/uploads\/2026\/11\/Combine-Settings-for-Soybeans.webp.webp","keywords":["case ih concaves","Combine","combine concaves","Complete","Deere","estes concaves","FieldTuning","Guide","JOHN","john deere concaves","Settings","Setup","soybeans","xpr concaves"],"articleSection":["Agriculture"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#respond"]}]},{"@type":"WebPage","@id":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002","url":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002","name":"John Deere Combine Settings for Soybeans: A Complete Setup and Field-Tuning Guide - Som2ny Network","isPartOf":{"@id":"https:\/\/peraltafinancing.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#primaryimage"},"image":{"@id":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#primaryimage"},"thumbnailUrl":"https:\/\/accountants4yourbusiness.co.uk\/wp-content\/uploads\/2026\/11\/Combine-Settings-for-Soybeans.webp.webp","datePublished":"2026-11-11T14:06:46+00:00","breadcrumb":{"@id":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/accountants4yourbusiness.co.uk\/?p=7078002"]}]},{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#primaryimage","url":"https:\/\/accountants4yourbusiness.co.uk\/wp-content\/uploads\/2026\/11\/Combine-Settings-for-Soybeans.webp.webp","contentUrl":"https:\/\/accountants4yourbusiness.co.uk\/wp-content\/uploads\/2026\/11\/Combine-Settings-for-Soybeans.webp.webp","width":1717,"height":916},{"@type":"BreadcrumbList","@id":"https:\/\/accountants4yourbusiness.co.uk\/?p=7078002#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/peraltafinancing.com\/?bp_activities=1"},{"@type":"ListItem","position":2,"name":"John Deere Combine Settings for Soybeans: A Complete Setup and Field-Tuning Guide"}]},{"@type":"WebSite","@id":"https:\/\/peraltafinancing.com\/#website","url":"https:\/\/peraltafinancing.com\/","name":"Som2ny Network","description":"Daily Deals","publisher":{"@id":"https:\/\/peraltafinancing.com\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/peraltafinancing.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":"Organization","@id":"https:\/\/peraltafinancing.com\/#organization","name":"Som2ny Network","url":"https:\/\/peraltafinancing.com\/","logo":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/peraltafinancing.com\/#\/schema\/logo\/image\/","url":"https:\/\/accountants4yourbusiness.co.uk\/wp-content\/uploads\/2026\/07\/4a0953c4-logo-300x86-1.png","contentUrl":"https:\/\/accountants4yourbusiness.co.uk\/wp-content\/uploads\/2026\/07\/4a0953c4-logo-300x86-1.png","width":300,"height":86,"caption":"Som2ny Network"},"image":{"@id":"https:\/\/peraltafinancing.com\/#\/schema\/logo\/image\/"}},{"@type":"Person","@id":"https:\/\/peraltafinancing.com\/#\/schema\/person\/b8eaddeb20a8727558e0d0cddcca426e","name":"admin","image":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/peraltafinancing.com\/#\/schema\/person\/image\/","url":"https:\/\/secure.gravatar.com\/avatar\/729ae85bf62b9917e93538db2f2688ca?s=96&r=g&default=https%3A%2F%2Faccountants4yourbusiness.co.uk%2Fwp-content%2Fplugins%2Fbuddypress-first-letter-avatar%2Fimages%2Fdefault%2F96%2Flatin_a.png","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/729ae85bf62b9917e93538db2f2688ca?s=96&r=g&default=https%3A%2F%2Faccountants4yourbusiness.co.uk%2Fwp-content%2Fplugins%2Fbuddypress-first-letter-avatar%2Fimages%2Fdefault%2F96%2Flatin_a.png","caption":"admin"},"sameAs":["https:\/\/accountants4yourbusiness.co.uk"],"url":"https:\/\/accountants4yourbusiness.co.uk\/?author=1"}]}},"_links":{"self":[{"href":"https:\/\/accountants4yourbusiness.co.uk\/index.php?rest_route=\/wp\/v2\/posts\/7078002","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/accountants4yourbusiness.co.uk\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/accountants4yourbusiness.co.uk\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/accountants4yourbusiness.co.uk\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/accountants4yourbusiness.co.uk\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=7078002"}],"version-history":[{"count":0,"href":"https:\/\/accountants4yourbusiness.co.uk\/index.php?rest_route=\/wp\/v2\/posts\/7078002\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/accountants4yourbusiness.co.uk\/index.php?rest_route=\/wp\/v2\/media\/7078003"}],"wp:attachment":[{"href":"https:\/\/accountants4yourbusiness.co.uk\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=7078002"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/accountants4yourbusiness.co.uk\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=7078002"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/accountants4yourbusiness.co.uk\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=7078002"},{"taxonomy":"dealstore","embeddable":true,"href":"https:\/\/accountants4yourbusiness.co.uk\/index.php?rest_route=%2Fwp%2Fv2%2Fdealstore&post=7078002"},{"taxonomy":"offerexpiration","embeddable":true,"href":"https:\/\/accountants4yourbusiness.co.uk\/index.php?rest_route=%2Fwp%2Fv2%2Fofferexpiration&post=7078002"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}