Air Vents Interrupting Crown Moulding? Several Beautiful Solutions!


Hi Everyone,

Oh my! My son Aaron is on his way from Tel Aviv. His plane is expected to arrive around 9:30 this morning!

 

Today’s post is actually a continuation of last week’s post about crown moulding failures. However, instead of a window treatment, the focus is on those ugly air vents that are located high up on a wall. Why, oh why, do they stick them up so high? In addition, the vents usually can’t be moved. Or if they can be moved, it would be prohibitively expensive to do so.

 

 

Sure, it would be fantastic if every example of a heating vent looked something like this wonderful example from Wadia Associates.

 

However, this requires careful planning and a fantastic contractor.

 

Last week we looked at the example below of the issue with the air vent.  It’s all too common. However, there are numerous mistakes in addition to the crown moulding.

 

crown moulding failure + hvac vent

 

In fact, I’m having trouble moving beyond the ceiling and walls that have an unfortunate case of chronic acne covered with paint. AKA orange peel, if I’m being kind.

 

The solution is either a new layer of 1/4″ sheetrock, or else a good skim coat.

 

At this point, the only option would be a skim coat.

The next issue, and some might disagree with me, but a double crown moulding (one on top of the cabinets and then again on the ceiling) is not something I would do. It should be one or the other, and usually that’s the ceiling. That is, unless they did a crown as I have in my lower level bathroom and embrasure hall center that acts like a mini tray ceiling. That’s because this moulding puts the crown on a different horizontal plane, and one can avoid the vertical stacking that we have here.

Orac Decor c305 Cornice moulding, embrasure hallway

You can see it better during construction because the damned LED lights weren’t in yet. They make the images a bit fuzzy. This moulding only comes down a couple of inches.

 

However, let’s put that issue aside for the time being and focus on the air vent that’s in a bad spot.

 

This particular vent is in the worst spot possible, and it’s butted up against the ceiling. Still, one can cut into the crown moulding, or leave it off altogether.

 


At this point, let’s look at some more examples of what not to do when confronted with poorly placed air vents near the ceiling.

 

Bad Solutions for air vents meeting crown moulding

 

The problem with all of these crowns is that all of them have too much of the moulding going down the wall.

As for the bottom three, I truly don’t understand why anyone thinks this is the best solution. Why highlight that which would be better off completely hidden?

 

Crown moulding vent bump-out - no good
I found this one on eBay.

 

So, let’s look at what I think are far better ways of handling air vents that are too close to the ceiling.

 

Better, but needs better crown + vent

The above is about the only one I found after extensive searching that is even close to being the correct way to handle these air vents. And while it is infinitely better than the images above, I’m still having some issues.

1. The crown is a bit bulky, and more of it should be on the ceiling, unless it’s much flatter.
2. The vent itself is a bit better, but there are even better, more upscale options out there.

 

Okay, time to see the examples I created.

 

Now, please know that the technology for heating hardware is changing all the time. And for a blog post, I am not going to go into some of the cool vents I discovered while researching this post. Therefore, please know that this isn’t the only solution, but it’s one I could live with.

 

Orac Decor cx176 crown moulding + Signature Hardware Appert wall register

The first example uses the same moulding I used in my bathroom niche and embrasure door ceilings. It is Orac Decor cx176, and you can also find it here, on my renovation list for the bathroom and lower-level entry. 

Here it is, below.

 

embrasure hall ceiling moulding by Orac Decor

The next option uses the moulding in the ceiling in front of the closets, which is at the bottom of this image with the gray-blue ceiling.

Orac Decor c305 crown moulding + Signature Hardware Appert wall register

Since this is a bit difficult to see, I made another graphic showing a 3/4 view of the one above and another attractive flat ceiling crown we looked at in the modern interior mouldings post. 

Two Orac Decor Crown Moulding Details with hv_ac vent
Stepped crown moulding from Orac Decor.

This is the same Orac Decor c353 moulding at the bottom of the graphic in the image above this one.

 

Signature Hardware vent cut into Cornice Store Art Deco moulding

 

Above is another moulding that combines a frieze that acts as a cornice. Because it is shallow, we can create a cutout for the Signature Hardware vent. Of course, it would be better if the entire vent were below the cornice. However, this is for those situations when the vent can’t be moved. The moulding is from an English company called the Cornice Store.

However, I found this interesting thread on Reddit where some pros discussed the possibility of moving a vent a bit with little fuss or expense.

 


One thing I forgot to mention is that when we’re talking about air vents for heating and air conditioning, there are two types.

 

The first is the supply register, or just register. This vent almost always has louvers that are adjustable and can move the air in different directions.

A return vent sucks the old air back in.

 These are grilles that don’t require louvers.

 

Below are some attractive register covers from Signature Hardware.

 


I used mouldings from Orac Decor all over my condo.

moulding delivery from heaven

Boxes, and boxes, and boxes. This is from February 2024.

The guys loved working with them, and I love living with them!

To see everything I used throughout my home, please go here.

Okay, that’s all for now. I’d better get some rest before my son shows up!

xo,

 

 

***Please check out the newly updated HOT SALES!  (Big sitewide sale at Serena & Lily! and a big weekend update with many early Black Friday Sales!)


***Also, the Laurel Home Holiday Shop is now 100% Open. It’s full of decor ideas and nine gift guides! Please check it out here!  🎄

 

Enjoying Laurel Bern Interiors?
You can buy me a coffee below. ☕

You will see an option to buy one, three or five coffees. (or more!) And, if so inclined, it can be a monthly gift. Whatever you can manage is appreciated more than I can say. And if it’s not feasible, of course, that’s okay too.

 Also, if you’re doing some shopping on Amazon, please click this Amazon affiliate link or the graphic below.

This website is very expensive to run, and in order to keep it (and myself) running, I’m depending on my kind readers clicking on the affiliate links before purchasing something you want to get. It costs you nothing, but if enough of you do it, it really helps!

 

Amazon ad

Thank you so much!

I very much appreciate your support of this website!

We will be happy to hear your thoughts

Leave a reply

Som2ny Network
Logo
Register New Account
Compare items
  • Total (0)
Compare
0
Shopping cart